worm motor
A robust worm-travel gearbox powered by an MM28 electric motor. Ideal applications where a simple to fit, high torque end result is required. Great for student based tasks which includes robots and buggies.
The machine has been designed so that the output shaft can be ‘clicked’ in and out for modification. E.g. cutting down to size. The motor is snap fitted into its cradle to activate
![\"\"](\"http:\/\/gearboxes-worm.xyz\/wp-content\/uploads\/2020\/03\/worm-motor.jpg\" "\\"\\"")
the apparatus and worm.Details
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + electric motor: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor is not turning. The high gear ratios of 216:1 or 336:1 make this gearbox appropriate for little strolling robots, lifting mechanisms, and various other applications where substantial torque is desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draw up to some amps, making them perfect candidates for the DRV8833 motor driver carrier. Engine overheating can be caused by excessive stalling, even at very low voltages. We advise that you utilize stall-detection sensors, or just see your robot, to ensure that it doesn\u2019t stall for more than a few seconds at the same time.
This gearbox has a 4 mm diameter, round output shaft, which works together with the wheels that are compatible with Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also fits on the smaller threaded end of the shaft, although it is not particularly intended to work with this kind of shaft (the hub\u2019s set screw could damage the thread on the shaft).
Ever-Power gear motors will be economical, right-angle, worm-geared motors that install easily found in the tightest applications. Economical correct position worm geared motors set new requirements for reliability, effectiveness and economic climate with unparalleled features which includes hollow shafts in the smallest sizes. An inverter friendly design offers easy integration today and a future proof remedy. The Ever-Power gear electric motor offers total flexibility in mounting choices includes shaft, base, face, and flange solutions. The motor terminal box can be mounted in option positions rotated in 90\u00ba steps around the motor frame providing for unparalleled integration options.
Ever-Power gear motors adhere to North American and International standards, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a true total answer for our global customers.
Excellent protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose evidence,and can be utilized outdoors or in wet and dusty environments without the use of additional enclosures. Full rated output is available at the result shaft of the machine.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50\/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With included inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category predicated on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the solution for applications requiring a part turn, optional dual output, or an inability for the motor to be back again driven. The DC correct angle equipment motors are created for constant and intermittent duty procedure. Our right angle equipment reducers are designed with a number of mounting plate options, making them well suited for a number of DC motor based applications. You can expect 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1\/43 to 3\/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are created to generate high torque in a small package size. Worm Gear Motors are great for applications that want a personal- locking or breaking characteristic since the result shaft can\u2019t rotate when there\u2019s no power used. Also, Worm Gearheads can transfer motion in 90 degrees. With various reduction ratios, precision cut gears, voltages and sizes, EP Items has a DC Worm Equipment Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking \/ Braking Features
Motion Transfer of 90 Degrees
Capability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Protection Door Locks \/ Industrial Conveying Systems \/ Security Gates \/ Teeth Chair \/ Ambulance Cots & Stretchers Quite a few DC Motors could be complimented with among our Worm Gearheads. EP Items will continue to work with you to design and produce a Worm Gear Electric motor that may optimize the performance of your unique application.
Built to your specific requirements
Engine Type: Brushed \/ Brushless \/ Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Trim \/ Round \/ Splined \/ Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical \/ Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm engine uses a metal gear box for strength and a higher torque output. Because of the special mechanical framework of the worm get the electric motor output shaft is usually self locking and will not be rotated.
This part uses a two wire connection and supports direction control and also PWM speed control. Rated voltage is 12v and will attain 40RPM, with a torque of 8kg\/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg\/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear models from EP DRIVESYSTEMS especially show their strength in applications where great gear ratios are essential. Our worm geared motors are consequently optimally suited for make use of in intralogistics, packaging technology and the food & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions enable simple and effective cleaning of the get system.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical substance, corrosion and abrasion resistant.
Flexibility
Our modular design give users optimum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are many applications that require drive systems, and each one of these has its unique requirements. The EP series worm equipment motors could be quickly and effectively adapted to satisfy your needs.
Worm gear models impress with their great power density and compact design. If required, we are able to also source them with the highly effective nsd tupH surface area treatment.
As well as the basic EP housing, we offer an extensive type of bolt-on components to customize the merchandise including torque arms, shaft addresses and output flanges. These can be easily field installed, but we will also be happy to assemble the average person components for you.
Discover more about the modular SI worm geared motors!
Find out more
Smooth and Tidy: The EP worm gear unit SMI
SMI worm gear products feature a even, corrosion-resistant alluminum alloy casing. Optional nsd tupH surface conversion makes this product preferably suited for harsh and demanding industries like food processing and pharmaceuticals.
Flexible input designs such as NEMA, IEC or immediate motor mounts in additional foot or flange mounted casing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared engine program. The units have got on all sides unique fixing possibilities and enable an easy assembling for the customer.
Additional drive configurationscan be created by use of built-in add-ons (e.g. torque arm and output flanges). The housings are made in light weight construction out of aluminium die cast. Motor attachment is realised in general through IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:result shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly\/installation:uniblock, flange, torque arm
Buy Worm Get Gearbox with Electric motor – incorporating the following features: 1 to 6V voltage rating, 17100 rpm no load speed, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm huge, 40mm high, a good robust worm travel gearbox powered by an MM28 motor (included), most suitable for applications where a simple to fit, high torque result is required, nylon housing and gear, requires light oil or silicon grease lubrication, perfect for student based tasks including robots and buggies.
Most ideal for applications where an easy to match, high torque outcome is required
Ideal for student based tasks including robots and buggies
Reversible Large torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Features:
The motor is Gear DC motor with micro-turbine worm, you can change the wiring-connection to improve motor rotation.
Turbo worm geared motor with self-lock, that’s, in the case of motor without electrical, the outcome axis is definitely fixed, self-lock.
The reducer output shaft arranged vertically with the electric motor shaft, whole motor output shaft relatively-short than general gear engine, trusted to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r\/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the home window, door, Mini winch. Ect.
In sumo robot or combat robot competition where large holding torque’s motor is essential in order to avoid your robot being pushed by your opponent robot. The worm equipment is definitely a much better option compared to the spur gear motor. How come worm gear so special? Take a look wiki out: Worm Travel.
“Unlike with ordinary gear trains, the direction of transmission (input shaft vs output shaft) is not reversible when using large reduction ratios, due to the better friction involved between the worm and worm-wheel, when usually a single start (1 spiral) worm is used. This is normally a advantage when it is desired to remove any possibility of the result driving the input.”
In other phrases, it is hard to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g<\/p>\n